Trail camera Specification
| Maximum image size | 30MP |
| Lens | f=7.36mm F/NO:2.8 FOV=55°; Auto IR-Cut-Remove (at night) |
| IR-Flash Range | 25m-30m; High Power LED : 4LEDS |
| Display Screen | 2.4 inch HD Color Display |
| Memory Card | SD or SDHC Card, up to 64GB |
| Image Size | 30MP(6400x4800);16MP(4736×3552);5M (2592X1944); |
| Video Size | 1920*1080;1280*720 ;640*480; |
| PIR Sensitivity | PIR with 4 sensitivity levels:High/ Normal/ Low/Auto |
| Operation | Day/Night |
| Response Time | Picture trigger:< 0.25 s ;Video trigger: <0.6s; |
| Triggering Interval | 1sec-60min programmable |
| Shutter Speed | 1/10-1/2000sec. |
| Shooting Numbers | 1-9 programmable |
| Video Length | 5-60sec. programmable |
| Power Supply | 8×AA recommended; DC12V |
| Stand-by Current | <75uA |
| Power Consumption | <140mA(500mA when IR-LED Lighted) |
| Timed Scan | programmable |
| Temperature Display | programmable |
| Camera Name | Input |
| Moon Display | programmable |
| Audio Video | programmable |
| User Interface | LCD display |
| Interface | USB;SD card; |
| Security | Strap;1/4-20 attachment |
| Operating Temperature | -20-60℃(Storage temperature:-30-70℃) |
| Operating Humidity | 5%-90% |
| Security Authentication | FCC/CE/RoHs/WEEE |
| Waterproof | IP67 |
Wildlife Camera Quick Start
Move the latches and open the front cover
Load 8 lithium AA or alkaline AA batteries
Insert the SD card
Switch to the SETUP Mode
Press MENU button
Press UP or DOWN key to select Camera or Video Mode
Put it good position
Switch to the ON Mode and it have started working.
Hunting Camera INTRODUCTION
This KEEPGUARD CAM is the best-selling scouting camera which is
designed for activity and is
resistant against water and snow. It is equipped with built-in
infrared LEDs, so that it can be triggered by any movement in a
location, then take high quality pictures or video clips.
Loading Batteries
After opening the two latches on the right side of the camera, you
will see that it has 8 battery slots.
For maximum battery life, we recommend using 8 lithium AA or
alkaline AA batteries.
Using an External Power Source
Optionally, you can connect an external 6V DC power source to the
"DC In" jack at the bottom of camera.
It is recommended to use a power source with a current output
greater than 1000mA. Please make sure
that the polarity is correct.
Inserting SD Card
This camera have 32MB internal memory, which is for camera upgrade.
Insert the SD card ( OFF mode )
before beginning to operate the camera. SD card is supported up to
maximum 32GB capacity.
Formatting the SD card
Formatting the SD card removes all files on the memory card and
prepares for camera. Press the MENU,
then RIGHT or LEFT key several more times to move to the “Format”
parameter setting menu. Press OK
key to enter sub-menu, Press the UP or DOWN key to highlight YES
and press OK.
THE OFF, ON, and SETUP MODES
The KEEPGUARD CAM has three basic operational modes:
OFF Mode
The OFF mode is the "safe" mode when any actions must be taken,
e.g. replacing the SD card or batteries,
or transporting the device. You will use OFF mode if you connect
the camera to a computer's USB port
to download your photos/videos.
ON Mode
Once in ON mode no manual controls are needed or possible (the
control keys have no effect). The
KEEPGUARD CAM will take photos or videos automatically (according
to its current parameter settings)
when it is triggered by the PIR sensor′s detection of activity in
the area it covers.
SETUP Mode
In the SETUP mode you can check and change the settings of the
KEEPGUARD CAM with the help of
built-in LCD. Moving the power switch to the SETUP position will
turn on the LCD display and you will see an information screen.
Fig. 1: SETUP Information Screen
SETUP Mode Shortcut Keys
- First switch to the SETUP Mode.
- Press MENU button.
- Press RIGHT or LEFT key scrolls to the next or previous parameter.
- Press UP or DOWN key to select setting for the currently parameter.
- Press OK to save the new setting.
- Then switch to ON Mode to take photos or videos.
Trail Camera Performance:
